View LB1960M_226684.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Ordering number : EN6191
LB1960M
Monolithic Digital IC
LB1960M
Fan Motor 2-Phase Half-Wave Driver
Features
Package Dimensions
* Dual power supply voltage design (5/12V) and wide voltage unit: mm 3032B-MFP8 handling range (3V also supported for rotation functions only) * Constant-voltage Hall bias power supply (1.3V across HBGND) assures stable Hall output over entire temperature and 8 power supply voltage range. External limiting resistor not required. * Built-in Hall amplifier with hysteresis (supports core without commutating pole) * Built-in lockup protection and automatic recovery circuits 1 5.1 (External capacitor for rotation detection need only be 0.1 F, allowing compact, cost-saving design) * Built-in output transistor with output withstand voltage 0.35 24Vmax/output current 500 mA (average), 1A (peak) * Built-in thermal protection circuit * Compact MFP-8 package. Low external parts count, easy wiring, and small PCB area allow use also with miniature fan motors.
[LB1960M]
0.625 1.8max
0.15 0.645
5
4
1.27
0.1
1.5
SANYO : MFP8
Specification
Absolute Maximum Ratings at Ta = 25C
Symbol Conditions VCC max Pd max With specified substrate * IOUTave IOUTpeak t 1 ms Maximum output voltage VOUT max Maximum HB output current IH max Operating temperature Topr Storage temperature Tstg * Specified substrate (114.3 x 76.1 x 1.5 mm3, glass epoxy) Parameter Maximum supply voltage Allowable power dissipation Maximum output current Ratings 18 600 500 1000 Internal 10 -30 to +85 -55 to +150 Unit V mW mA mA V mA C C
Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
63099RM(KI) No. 6191-1/4
5.15 6.4
4.4
LB1960M
Allowable Operating Ranges at Ta = 25C
Parameter Recommended supply voltage Common mode input voltage range Symbol VCC 1 VCOM Conditions Ratings 3.6 to 17 0.2 to HB Unit V V
Electrical Characteristics at Ta = 25C, VCC = 12V
Parameter Circuit current Symbol ICC Conditions In drive mode (CT = L) In lockup protection mode (CT = H) VCT = 0.2V VCT = 8V min Ratings typ 2.3 3 0.8 1.2 0.16 0.24 4.0 6.8 1.4 22.5 5.0 7.2 1.6 23.5 1.0 6 1.3 180 max 4 5 2.0 0.4 7.0 7.6 1.8 24.5 1.3 12 1.5 210 Unit mA mA A A - V V V V mV V C
CT capacitor charge current ICT1 Capacitor discharge current ICT2 Capacitor charge/discharge current RCT RCT = ICT1/ICT2 ratio CT charge voltage VCT1 CT discharge voltage VCT2 Output limiter withstand voltage VOLM Io = 1 mA Output saturation voltage VOsat Io = 500 mA Hall input sensitivity VHN Including offset and hysteresis HB output H voltage VHBH RH = 350 Thermal protection trigger temperature T TSD Assured design target* * Assured design target: Target value, not measured individually
1.1 150
Pd max - Ta
1000
Allowable power dissipation, Pd max - mW
Specified substrate (glass epoxy, 114.3x76.1x1.5mm3)
800
600
400 312mW 200
0 -30
0
30
60
90
120
Ambient temperature, Ta - C
Truth Table
IN- H L - IN+ L H - CT L H OUT1 L H off OUT2 H L off Mode Rotating Lock-up protection activated
No. 6191-2/4
LB1960M
Pin Assignment
IN+ 1 HB+ 2
LB1960M
8 VCC 7 CT 6 OUT2 5 GND
IN- 3 OUT1 4
Top view
Sample Application Circuit 5/12V power supply (3.8 to 18V)
VCC HB+ RH H IN+ IN- OUT2 OUT1
CT 0.1 F GND
On-board parts
Precautions * If CT pin is connected to GND, the lockup protection and restart functions are disabled. * In a circuit configuration as shown above, a power supply/GND reverse connection will cause a current to flow as follows: GND -> OUT -> coil -> power supply. The value of this current is limited by the coil resistance. If it is less than 500 mA, the IC will not be destroyed. If required, insert a diode between VCC and the coil.
No. 6191-3/4
LB1960M
Block Diagram and Sample Application Circuit
Thermal protection circuit
L1
L2
VCC HB+
Constant voltage output circuit
OUT1
IN+
Control block
IN-
H
OUT2
Constant current source
CT C1 0.1 to 1 F
GND
Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of June, 1999. Specifications and information herein are subject to change without notice. PS No. 6191-4/4

▲Up To Search▲

Price & Availability of LB1960M

	To Download LB1960M Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .